YOUR PLUMBING CRASH COURSE: A GUIDE TO INSTALLING A BATHTUB

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Blog Article

Click Here

Do you find yourself in search of help concerning A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub Yourself
Setting up a bath tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a new one is additionally a moderately hard job. If the old tub is readily accessible, the project can move speedily; if you need to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the new one. Make sure you have actually qualified yourself for the work and fit attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is better to take into consideration employing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new bath tub in your shower room if you have currently bought a brand-new tub and also do not require to transform the plan of your previous supply of water pipelines.
Your devices as well as material list must make up the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited access that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel ready for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
    Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, place the faucet in the placing hole in the bath/basin making sure that the washers are in place between the faucet and the sink. Secure the faucet in place with the manufacturer offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind ought to be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Mounting the Tub


    Utilizing the two wood boards under its feet, position the bath tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
    The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bathtub up until the spirit level reads degree.
    To mount faucets, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the various other tap.
    Turn on the water supply as well as check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as additionally check the overflow electrical outlet and the regular outlet for leaks.
    Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has been used at least when as this will resolve it into its final position.

    Planning for the Installation


    Firstly, the supporting structure provided with the bath ought to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop stress on the bathtub.
    Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
    Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final setting.

    Tiling Around the Tub


    In the area where the bathroom meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing problems with moisture and possible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealant can split rather early if you do not take into consideration this activity before sealing.
    Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly available on the market. It is advisable to fit the tiles making use of water-resistant or water resistant sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I'm certainly very serious about Tools You Need to Install a New Bathtub and I am praying you appreciated our entry. I beg you take a moment to share this page if you enjoyed reading it. Thank you for your time spent reading it.


    Book Services

    Report this page